機械社區

 找回密碼
 注冊會員

QQ登錄

只需一步,快速開始

搜索
查看: 3066|回復: 1
打印 上一主題 下一主題

求教花鍵軸中的相對角度加工工藝

[復制鏈接]
跳轉到指定樓層
1#
發表于 2016-1-26 11:24:41 | 只看該作者 回帖獎勵 |倒序瀏覽 |閱讀模式
本帖最后由 BB7290 于 2016-1-26 11:28 編輯 4 e- g# G5 P: @  m7 F# @
3 o2 Y0 u* M! R9 u( t1 e
如圖,其中兩頭的花鍵相對于中間花鍵的88度,怎么控制得到?謝謝。
" T& V8 Q' K- t% Z# V: D' c5 m, k0 H& O2 U$ m6 j. I( @9 ~" g
補充:其給的工藝文件上是這樣說明的。& n7 y6 g7 G! l( _) c, R
Atention: The tooth gap 34T which is held on the drag fixuture must be painted or marked and it will be the reference to position the gap of the splines in relation to the slot and the thread.
- {0 F& `$ E$ v( v# j/ F  J% _
9 B9 C9 ~9 m+ m1 Q3 {. }ATENTION: Hold the drag fixuture in the centra tooth gap 34T, making one tooth gap 30T coincident to this tooth gap 34T after machining it and in which the drag fixture was held as it is showed at this draft.8 J+ k- G$ Y* _
9 p( ~' |! p$ V7 I) l( P
REMARK : Do not take out the drag fixture after machining the first side of the splines and while turning around the piece to machine the second side of the splines to keep the alignment between the splines of the both end sides B and C showed at this draft.# M6 \! _& q1 n; A* I1 V  \( ^  ~

9 Z$ k  W/ H7 v0 w6 C' [  x1 Ratention :End Sides Splines B and C must be aligned within +-10minutes.
. \: o& C. I+ T  V/ S$ l
, r  X" F' x' n% @* M; `! g' C" |% F! @3 ?$ N" r0 n; h
補充內容 (2016-1-26 16:20):  j; x4 h" t' l9 i4 n3 m
需對齒的花鍵軸加工

本帖子中包含更多資源

您需要 登錄 才可以下載或查看,沒有帳號?注冊會員

x
回復

使用道具 舉報

2#
發表于 2016-1-26 12:59:49 | 只看該作者
坐等高人         
回復 支持 反對

使用道具 舉報

您需要登錄后才可以回帖 登錄 | 注冊會員

本版積分規則

小黑屋|手機版|Archiver|機械社區 ( 京ICP備10217105號-1,京ICP證050210號,浙公網安備33038202004372號 )

GMT+8, 2024-10-31 13:30 , Processed in 0.054316 second(s), 20 queries , Gzip On.

Powered by Discuz! X3.4 Licensed

© 2001-2017 Comsenz Inc.

快速回復 返回頂部 返回列表