FANUC 0i-D 維修說明書_新

數控散人

- ]$ z/ b  X' l( X3 n4 ZFANUC Series 0 -MODEL D
$ G: Y4 o3 ~/ R; `FANUC Series 0 Mate-MODEL D
維修說明書
. E  A- @1 {) D+ C2 @5 |
7 Y$ }9 O8 m1 u" E' L8 {目錄
. j: x5 T0 S" w- w1 h( p+ u4 A& w......
) |7 s* l* R* w2 i" m! y/ R- F6 數字伺服..................................................................................... 336
' ^$ D2 J2 Q- v9 F4 @6.1 伺服參數的初始設定方法 .................................................................... 337
6.2 FSSB數據的顯示和設定畫面................................................................... 347
  _6 Z1 \' j# K5 i0 D8 a  w6.3 伺服調整畫面............................................................................... 355
6.3.1 參數的設定................................................................................355
# N1 v, r; v& d6.3.2 顯示伺服調整畫面..........................................................................355
9 f; y5 P/ ~- ?" }* A6.3.3 與放大器和電機相關的報警..................................................................357
6.3.4 αi 脈沖編碼器相關的報警...................................................................358
( F5 D. F6 o; I# Y! Y: A8 P% S6.3.5 與串行脈沖編碼器通信相關的報警............................................................359
6.3.6 與斷線相關的報警..........................................................................359
6.3.7 參數非法報警..............................................................................360
" G/ t# Z) w4 Z: I. I0 e: j6.3.8 其他報警..................................................................................360
! g' @8 y% V0 V+ u0 t8 b: X2 z- y* I6.4 調整返回參考點位置（擋塊方式）............................................................. 362
8 \9 L3 a* G& j3 z6.5 無擋塊參考點設定........................................................................... 366
6.6 αi 伺服的警告接口.......................................................................... 368
6.7 αi 伺服信息畫面............................................................................ 369
7 AC 主軸...................................................................................... 373
7.1 串行接口AC 主軸............................................................................ 374
7.1.1 主軸控制概要..............................................................................374
, k% {& N+ V3 ]+ K7.1.1.1 M系列齒輪切換方式A (參數SGB (No.3705#2 = 0))............................................375
1 C" M/ {9 ~' c; ^7.1.1.2 M系列齒輪切換方式B (參數SGB (No.3705#2 = 1))............................................375
, m3 g- I5 s1 G. |- v7 y/ K7.1.1.3 T系列.................................................................................. 375
7.1.2 主軸設定調整畫面 .........................................................................376
$ y. S8 C' {+ ]5 L7.1.2.1 顯示方法............................................................................... 376
) L. C  I! v3 k7.1.2.2 主軸設定畫面........................................................................... 377
( g9 ~% [0 \& m# T7.1.2.3 主軸調整畫面........................................................................... 378
7.1.2.4 主軸監控畫面........................................................................... 380
% c3 d! f' C  W/ Q, G6 B4 p7.1.2.5 與調整畫面上的運行方式對應的參數號......................................................382
......
% N0 z8 u2 Q: K; A2 S; e+ q
[ 本帖最后由 數控散人 于 2009-3-10 09:31 編輯 ]

wujp

0i-D
30i/31i/32i
fanuc 最近推出的系統

ghostcnc

瞧瞧看�。。。。。。�！

poi_poi

謝謝��！

謝謝��！

heyue1213

下來看看哦

liukai19760410

下了,謝謝樓主.

yamgjishi

權限不夠?？？？？？？？？？？？？？

gaotenghuan

怎么不能下載，版主快來解決 ，等你

langxb

不能下載，版主快來解決

傻氣胖子

滅有那么多分！~~~~~~~~~~~~